Forum Donations 2024/2025
on October 25, 2024, 09:29:59 am
HI Guys The funds from the last donation effort ran out in July. The hosting cost are €22 a month. Ive created a goFundMe as the paypal pools only last one month. https://gofund.me/1bd89a45Thanks again for your support 
Re: Which brake pads and discs?
Last Poster: mcgc0 in Mk5 General Area on Today at 11:33:29 am
Brembo used to be a decent brand until the pads started to be produced by the chinese fuf knows who makes the discs One things for certain they love to rust
Interesting, and a shame at the same time. Drags the brand down. Brembo once the go-to for brakes.
Re: Side Sill Cover
Last Poster: mcgc0 in Mk5 General Area on Today at 11:27:53 am
Slow progress so far. UK sill covers I ordered on eBay were non-OEM and are thin grey smooth plastic type that need priming then top/final coat - my fault, I should have checked first. Taking the hit and return posting these.
The LLL part recommended earlier, when I checked availability, replied back to say part # 1K4 853 859 B 9B9 is no longer supported/offered, which i
Wrong steering module for paddles?
Last Poster: flabbymallow in Mk5 General Area on Yesterday at 01:13:05 am
Hi everyone,
I bought myself an mk5 r32 steering wheel with paddles and no MFSW to fit to my mk5 gti which has neither paddles or MFSW at the moment.
Throuhg my research I came to the conclusion that I did not need to replace the steering module as it seemed that as long as you had a dsg installed it was possible to recode the module to accept the paddles. Aft
Rear arb bushes
Last Poster: Kontiki in Mk5 General Area on December 23, 2024, 06:56:24 pm
Hi folks , currently refreshing the rear suspension on my 2008 gti , having a problem with the rear arb bushes, ordered a set of bushes complete with brackets and bolts when I came to fit them the internal diameter of the bush is way to small . I believe I need 20.7 diameter is this correct? , any suggestions and if possible a part number, thanks in anticipation Colin.
Re: Oil pressure warning & need advice.
Last Poster: NikoG93 in Mk5 General Area on December 21, 2024, 08:25:59 pm
Don’t like shouting out bad news but you’ve said that it’s been sitting. Maybe rod bearings? I would try dumping a few cans of engine flush additives. Make sure there isn’t a double oring on the oil filter housing.
How would rod bearings be affected from vehicle sitting? Nev
Re: Vanilla GTI
Last Poster: MKVASMR in Members Rides on December 21, 2024, 06:27:08 pm
Recently got myself a 🎁#127873 and installed a non res Milltek catback. Really happy how it looks.   This afternoon had some
Re: SEAT Help
Last Poster: lazy in Mk5 General Area on December 19, 2024, 08:17:24 am
I remember a few years ago reading that what someone had done with theirs after replacing the lumbar support a few times and it repeatedly breaking, they cable tied the two pieces together and it worked well for them. Unfortunately I can't give you any more information because I haven't had one of these seats apart, but I hope that's of some help to you.
Re: Alex's Shadow Blue GTI
Last Poster: mk1mad in Members Rides on December 17, 2024, 12:00:55 pm
Good work, look forward to seeing what you did to refresh the rear beam and underside. This is a job to do on mine next spring.
Throttle body
Last Poster: Zmenu in Mk5 General Area on December 16, 2024, 07:55:12 am
Help!
Hi, I have problem of my throttle body, It is open 100% all the time. And i am getting 11.8 V, 3.2 V, 12.2V and 0 volts on the wiring harness. What is the correct voltage of the wiring harness? I checked also at the pcm and gott the same voltage.
The car is VW golf plus 1.9 tdi automatic gear, 2007 model.
Throttle body
Last Poster: Zmenu in How to Guides / Troubleshooting on December 15, 2024, 10:58:24 pm
Help!
Hi, I have problem of my throttle body, It is open 100% all the time. And i am getting 11.8 V, 3.2 V, 12.2V and 0 volts on the wiring harness. What is the correct voltage of the wiring harness? I checked also at the pcm and gott the same voltage.
The car is VW golf plus 1.9tdi , automatic gear ,2007
Milltek exhaust leak
Last Poster: MKVASMR in Mk5 General Area on December 15, 2024, 03:27:50 pm
Hi guys, I’ve fitted a cat back Milltek exhaust and after a few days I’ve noticed some soot on the clamps.
I did it as I saw it on another forum with the clamps being on the end of connections.
I’ve also put some GumGum exhaust paste before sliding the parts together.
Is there a specific torque for the clamp bolts? I did it hand tight, didn’t wanted to use an impac
|
 Users: 0 Guests: 456
|
